- parametric-filter Amplifiers
- parametric-filter Audio
- parametric-filter Battery management ICs
- parametric-filter
- parametric-filter DLP products
- parametric-filter Data converters
- parametric-filter
- parametric-filter Interface
- parametric-filter Isolation
- parametric-filter
- parametric-filter
- parametric-filter Motor drivers
- parametric-filter Power management
- parametric-filter
- parametric-filter Sensors
- parametric-filter
- parametric-filter Wireless connectivity
- parametric-filter Comparators
- parametric-filter Current-sense amplifiers
- parametric-filter Difference amplifiers
- parametric-filter Fully differential amplifiers
- parametric-filter Instrumentation amplifiers
- parametric-filter Operational amplifiers (op amps)
- parametric-filter
- parametric-filter Special function amplifiers
Home
Amplifiers
Comparators
Low offset, quad differential comparator
Data sheet
- document-pdfAcrobat LMx39-N, LM2901-N, LM3302-N Low-Power Low-Offset Voltage Quad Comparators datasheet (Rev. E) PDF | HTML
Product details
- Wide Supply Voltage Range
- LM139/139A Series 2 to 36 VDC or ±1
to ±18 VDC - LM2901-N: 2 to 36 VDC or ±1 to ±18 VDC
- LM3302-N: 2 to 28 VDC or ±1 to ±14 VDC
- Very Low Supply Current Drain (0.8 mA) –
Independent of Supply Voltage - Low Input Biasing Current: 25 nA
- Low Input Offset Current: ±5 nA
- Offset Voltage: ±3 mV
- Input Common-Mode Voltage Range Includes
GND - Differential Input Voltage Range Equal to
the Power Supply Voltage - Low Output Saturation Voltage: 250 mV at 4 mA
- Output Voltage Compatible With TTL, DTL, ECL,
MOS, and CMOS Logic Systems - Advantages:
- High-Precision Comparators
- Reduced VOS Drift Overtemperature
- Eliminates Need for Dual Supplies
- Allows Sensing Near GND
- Compatible With All Forms of Logic
- Power Drain Suitable for Battery Operation
- Wide Supply Voltage Range
- LM139/139A Series 2 to 36 VDC or ±1
to ±18 VDC - LM2901-N: 2 to 36 VDC or ±1 to ±18 VDC
- LM3302-N: 2 to 28 VDC or ±1 to ±14 VDC
- Very Low Supply Current Drain (0.8 mA) –
Independent of Supply Voltage - Low Input Biasing Current: 25 nA
- Low Input Offset Current: ±5 nA
- Offset Voltage: ±3 mV
- Input Common-Mode Voltage Range Includes
GND - Differential Input Voltage Range Equal to
the Power Supply Voltage - Low Output Saturation Voltage: 250 mV at 4 mA
- Output Voltage Compatible With TTL, DTL, ECL,
MOS, and CMOS Logic Systems - Advantages:
- High-Precision Comparators
- Reduced VOS Drift Overtemperature
- Eliminates Need for Dual Supplies
- Allows Sensing Near GND
- Compatible With All Forms of Logic
- Power Drain Suitable for Battery Operation
The LMx39-N series consists of four independent precision voltage comparators with an offset voltage specification as low as 2 mV maximum for all four comparators. These comparators were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. These comparators also have a unique characteristic in that the input common-mode voltage range includes ground, even though they are operated from a single power supply voltage.
The LMx39-N series was designed to directly interface with TTL and CMOS. When operated from both plus and minus power supplies, the devices directly interface with MOS logic where the low power drain of the LM339 is a distinct advantage over standard comparators.
The LMx39-N series consists of four independent precision voltage comparators with an offset voltage specification as low as 2 mV maximum for all four comparators. These comparators were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. These comparators also have a unique characteristic in that the input common-mode voltage range includes ground, even though they are operated from a single power supply voltage.
The LMx39-N series was designed to directly interface with TTL and CMOS. When operated from both plus and minus power supplies, the devices directly interface with MOS logic where the low power drain of the LM339 is a distinct advantage over standard comparators.
open-in-new Find other Comparators
Technical documentation
No results found. Please clear your search and try again.
View all 5Type | Title | Date | ||
---|---|---|---|---|
* | Data sheet | LMx39-N, LM2901-N, LM3302-N Low-Power Low-Offset Voltage Quad Comparators datasheet (Rev. E) | PDF | HTML | 31 Dec 2014 |
E-book | The Signal e-book: A compendium of blog posts on op amp design topics | 28 Mar 2017 | ||
More literature | Die D/S LM2901 MDA MWA Low Power Low Offset Voltage Quad Comparators | 08 Jan 2013 | ||
More literature | Die D/S LM2901 MDA Low Power Low Offset Voltage Quad Comparator | 20 Sep 2012 | ||
More literature | Die D/S LM2901 MWC Low Power Low Offset Voltage Quad Comparator | 20 Sep 2012 |
Design & development
For additional terms or required resources, click any title below to view the detail page where available.
Simulation tool
PSPICE-FOR-TI — PSpice® for TI design and simulation tool
PSpice® for TI is a design and simulation environment that helps evaluate functionality of analog circuits. This full-featured, design and simulation suite uses an analog analysis engine from Cadence®. Available at no cost, PSpice for TI includes one of the largest model libraries in the (...)
Simulation tool
TINA-TI — SPICE-based analog simulation program
TINA-TI provides all the conventional DC, transient and frequency domain analysis of SPICE and much more. TINA has extensive post-processing capability that allows you to format results the way you want them. Virtual instruments allow you to select input waveforms and probe circuit nodes voltages (...)
User guide: PDF
Package | Pins | Download |
---|---|---|
PDIP (N) | 14 | View options |
SOIC (D) | 14 | View options |
TI's Standard Terms and Conditions for Evaluation Items apply.
Ordering & quality
Add a quantity to your cart and begin the checkout process to view the options available to select lot or date codes from existing inventory.
Learn more
Information included:
- RoHS
- REACH
- Device marking
- Lead finish/Ball material
- MSL rating/Peak reflow
- MTBF/FIT estimates
- Material content
- Qualification summary
- Ongoing reliability monitoring
Information included:
- Fab location
- Assembly location
Recommended products may have parameters, evaluation modules or reference designs related to this TI product.
Support & training
TI E2E™ forums with technical support from TI engineers
Content is provided "as is" by TI and community contributors and does not constitute TI specifications. See terms of use.
If you have questions about quality, packaging or ordering TI products, see TI support.
Video series
View all videos